標準型用英語怎麼說?

標準型用英語怎麼說

標準型

[詞典] normalized form; standard form;

[例句]同時，可根據客戶的要求設計和製造非標準型電氣產品。

At the same time, according to the requirements of customers design and manufacture of non-standard electrical products.

"不符合標準的" 英語怎麼說

Do not conform to the standards或者Non-compliant

羚羊用英語怎麼說？

羚羊

[釋義] antelope

[例句]研究的對象是尼羅河驢羚，一個瀕危的羚羊品種。

The study in question was of nile lechwe , an endangered antelope .

保證正確率，望採納

如有疑問，請追問

二進制,八進制，十進制，十六進制的英語單詞是什麼

二進制 Binary system

八進制 Octal number system

十進制 Decimal system

十六進制 Hexadecimal

123,221,200英語怎麼說

123,221,200這三個數字的英語表達如下

123：one hundred and twenty-three

221：two hundred and twenty-one

200：two hundred

把下面的翻譯成英文，謝謝

Abstract: The fuel tank of the tank roof structure depends on the components installed on it. 箱頂上一般要設置空氣濾清器，注油口，空氣濾清器通常為附帶注油口的結構，取下通氣帽可以注油，放回通氣帽即成空氣濾清器。 To set the box on top of the general air filter, fuel injection port, usually with oiling the air filter structure of the mouth, remove the ventilation cap can be oiling, back into the ventilation cap is needed for the air filter. 對於鋼板焊接的油箱，箱頂上安裝液壓泵組時，側板厚度應適當加大。 For welded steel tank, installation of pump set top box, the side panel thickness should be appropriately increased. 為了延長油液在油箱中逗留的時間。 Oil in the fuel tank in order to extend the time of stay. 促進油液在油箱中的環流，使更多的油液參與系統的循環，從而更好地發揮油箱的散熱、除氣、沉澱等功能，油箱中，尤其在油液容量超過100L的油箱中應設置內部隔板，隔板要把系統回油區隔開，並儘可能使油液在油箱內沿著油箱壁環流。 To promote the circulation of oil in the tank, so that more oil involved in the cycle of the system to better play to the cooling tank, in addition to gas, precipitation and other functions, the tank, particularly in the oil capacity of more than 100L of fuel tank should be Set the internal partitions, partitions should separate the system back to oil and oil as much as possible within the tank along the tank wall in the circulation. 隔板缺口處要有足夠大的過流面積，使環流流速為0.3-0.6m/s。 Partition must be large enough gap in the over flow area so that circulation flow rate of 0.3-0.6m / s. 隔板結構有溢流式標準型、溢流式和迴流式等多種型式，溢流式隔板的高度不應低於液麵高度的2/3,隔壁下部應有開缺口，以使吸油側的沉澱物經此缺口至回油側，並經放油口排口關鍵詞；液壓油箱結構輔助元件表面處理 Clapboard structure standard overflow, overflow and the return type and many other ty......