記本開機錯誤程式碼解析大全

　　本文為大家帶來筆，希望能幫到大家。

　　Symptom / Error ***開機錯誤程式碼*** FRU / Action in Sequence***檢查範圍及解決方法***

　　10X

　　101: Interrupt failure;***中斷故障***

　　102: Timer failure;***計時器故障***

　　103: Timer interrupt failure; ***計時器中斷故障***

　　104: Protected mode failure; ***保護模式故障***

　　105: Last 8042 command not accepted;

　　107: NMI test failure;***NMI 測試失敗***

　　108: Timer bus test failure.

　　109: Low meg-chip select test. 1. System board. ***主機板問題***

　　110 :***Planar parity.*** ***記憶體奇偶校驗出錯*** 1. Go to Memory Checkout 2. DIMM card.3. Detach the expansion unit if it is attached to the computer.4. System board.

　　111:***I/O parity.*** 1. Go to Memory Checkout2. Expansion unit or port replicator.3. System board.

　　11XX

　　1101: Serial_A test failure.***A 序列口測試失敗*** 1. Serial device ***序列裝置***2. Communication cable ***相關通訊電纜***3. System board ***主機板***

　　12XX

　　1201: Serial_B test failure.***B 序列口測試失敗*** 1. System board ***infrared*** ***檢查主機板：紅外線口***

　　158 :***Hard disk password was not set even though the supervisor password is set.*** ***超級使用者密碼已設，但硬碟密碼沒有設定*** 1. Set the password for hard disk drive.***設定硬碟密碼***

　　159 :***Hard disk password is not set the same as the supervisor password.*** ***硬碟密碼與超級使用者密碼不一樣*** 1. Set the correct password for hard disk drive.***設定正確的硬碟密碼***

　　161:***Dead battery.*** ***CMOS 電池不行*** 1. Go to Checking the Backup Battery 2. Backup battery.***CMOS 備份電池，在記憶體插槽旁邊***3. System board. ***主機板***

　　163:***Time and date were not set.*** ***系統時間沒有設好或混亂*** 1. Set time and date.***設定正確的系 統時間*** 2. System board. ***主機板問題***

　　173:***Configuration data was lost.*** ***CMOS 裝置配置資訊丟失*** 1. Select OK in the error screen; then set the time and date.***在 開機 ERROR 畫面上按OK，然後設定系統時間***2. Backup battery. ***CMOS 電池需要更換***3. System board. ***主機板問題***

　　174:***Configuration error: Perform Checking the Installed Devices List before changing any FRUs.*** 1. Check device configuration.2. Hard disk drive assembly.3. System board.

　　175

　　177

　　178175: EEPROM CRC #1 error.

　　177: Supervisor password check sum error.

　　178: EEPROM is not functional. 1. System board. ***檢查主機板***

　　17XX

　　1701: Hard disk controller failure. ***硬碟控制器故障***

　　1780, 1790: Hard disk 0 error. ***主硬碟有問題***

　　1781, 1791: Hard disk 1 error.***從硬碟有問題*** 1. Hard disk drive ***檢查硬碟***

　　2. System board ***檢查主機板***

　　183 :***Incorrect password entered at the supervisor password prompt.*** ***超級使用者開機密碼不對*** 1. Have the user examine the password.***請使用者檢查密碼***

　　184:***Power-on password check sum error.*** ***Power-on 密碼有誤*** 1. Reset the power-on password in Easy-Setup.***重設Power-on 密碼***

　　185:***The startup sequence is not valid. Suspect that power was off when the startup sequence was being updated.*** ***系統啟動順序無效，懷疑是更新啟動順序時電源關掉*** 1. Reset the startup sequence in Easy-Setup.***在Easy-Setup 重設啟動順序***

　　186 :1. System board. ***檢查主機板***

　　190:***A depleted battery pack was installed when the power was on.******開機時，機內筆記本電池已快耗盡了*** 1. Go to Checking the Battery Pack.***更換機內筆記本電池 ***

　　191XX:***PM initialization error.*** ***PM 初始化錯誤*** 1. System board. ***檢查主機板***

　　192:***Fan error.*** ***CPU 散熱風扇故障*** 1. Measure the voltage of the backup battery. If thevoltage is not correct, replace the backup battery.***檢查CMOS 備份電池的電壓，電壓不行時更換 電池*** 2. Fan ***要更換CPU風扇***3. System board ***主機板問題***

　　195:***The configuration read from the hibernation area does not match the actual configuration.*** ***從休眠區域讀到的系統配置資訊與實際配置不同*** 1. Check if the config uration was changed. For example, check if the DIMM card is added.***檢查配置是否改動，記憶體有無增加等***

　　196:***A read error occurred in the hibernation area of the hard disk drive.****** 從硬碟的休眠區域中讀寫時，發生錯誤*** 1. Run the hard disk drive test. ***測試硬碟***2. Hard disk drive.***檢查硬碟*** 199XX***Resume error.*** 1. System board.

　　1XX 1. System board. 2XX ***記憶體問題***201: Memory data error.

　　202: Memory line error 00-15.203: Memory line error 16-23.

　　205: Memory test failure on on-boardmemory.

　　221: ROM to RAM remap error. 1. Go to Memory Checkout.2. DIMM card. 3. System board. 225***Unsupported memory module.*** 1. Check if the supported DIMM is installed.2. DIMM card.3. System board.

　　301, 303, 304, 305, 3XX

　　***301: Keyboard error.*** ***筆記本鍵盤故障，301這個故障經常出現，往往是筆記本剛開機時，不小心

　　按住鍵盤所造成的，一般只要重啟電腦即可;*** 1. Go to Keyboard or Auxiliary Input Device Checkout 2. Keyboard.3. External numeric keypad. 4. External keyboard. 5. Keyboard/mouse cable.6. System board.

　　601, 6XX ***601: Diskette drive or controller error.****** 軟碟機或軟碟機控制器故障*** 1. Go to Diskette Drive Checkout.2. Diskette drive assembly. ***軟碟機有沒有裝配好?***3. Diskette. 4. System board. ***檢查主機板 ***

　　602:***Diskette read error.***; ***軟碟機讀故障*** 1. Go to Diskette Drive Checkout2. Diskette. 3. Diskette drive assembly.***軟碟機有沒有裝配好?***

　　604:***Unacceptable ID was read from the diskette drive.***; 1. Go to Diskette Drive Checkout2. Diskette drive assembly.3. System board.

　　2402 1. TV Out Card 24XX***2401: System board video error.*** ;***主機板顯示部分有問題*** 1. System board.***檢查主機板相關部 分***

　　808X

　　8081: PCMCIA presence test failure.***PCMCIA revision number also checked.***

　　8082: PCMCIA register test failure. 1. PC Card slot assembly.2. PCMCIA device. 3. System board. 860X***Pointing device error when TrackPoint is disabled.******當指點杆禁用時，外接的指點裝置有故障***;

　　8601: System bus error-8042 mouse interface.

　　8602: External mouse error.***外接滑鼠故障***;

　　8603: System bus error or mouse error. ***匯流排或滑鼠故障***; 1. External mouse. ***檢查外接滑鼠***;2. External keyboard. ***檢查外接鍵盤***;3. System board.***檢查主機板***;

　　861X***Pointing device error when TrackPoint is enabled.******當指點杆啟用時，外接的指點裝置有故障***;

　　8611: System bus error-I/F between 8042 and IPDC.

　　8612: TrackPoint error.

　　8613: System board or TrackPoint error. 1. Reseat the keyboard cable on the subcard.***把鍵盤連線主機板的線，重插拔一下***;2. Keyboard ***檢查鍵盤***;3. External mouse ***檢查 外接滑鼠***;4. Sub card ***主機板上連線鍵盤的子卡***;5. System board ***主機板***; I9990301I

　　9990302I9990305

　　I9990301: Hard disk error. ***硬碟有故障***;

　　I9990302: Invalid hard disk boot record. ***無效的硬碟引導紀錄***;

　　I9990305: No bootable device. ***無可用的啟動引導裝置***; 1. Check that the operating system is installed in the hard disk drive. If not, install the operating system.***檢查硬碟上有否安裝作業系統***;2. Reseat the boot device.***重新設定可啟動的裝置***;3. Check the startup sequence for the correct boot device.***檢查啟動順序是否跟裝置正確對應 ***;

　　4. Check that the operating system has no failure and is installed correctly.***檢查電腦的操 作系統是否安裝正確***;

　　I9990303***Bank-2 flash ROM check sum error.*** 1. System board.

　　Other codes not listed above. 1. Go to Undetermined